ConvertiBARS - Original
The Rhino - Adjustable Clip-ons
Stunt Series ConvertiBARS and Accessories
Bike Specific Kits
Additional Completion Products
Lines & Cables
Front Brake Lines
How It Works
Nav Menu 2
Nav Menu 3
Nav Menu 4
Nav Menu 5
Nav Menu 6
Nav Menu 7
Nav Menu 8
Honda VFR-800(02-13) Bike Specific Kit
Price with Selected Options:
The Original Convertible Handlebar System
Black 43mm Convertible Handlebar Set (With V-ROC Technology) Fits 43mm OD Forks
Silver 43mm Convertible Handlebar Set (With V-ROC Technology) Fits 43mm OD Forks
Bike Specific Completion Pack
Front Brake Line:
Silver/Clear (Alt-2 Dual-two lines) 3 inches Longer Than Stock [Add $98.95]
Black/Black (Alt-2 Dual-two lines) 3 inches Longer Than Stock [Add $109.95]
Silver/Clear (Hydraulic) 3 inches Longer Than Stock, Teflon lined, Steel Braided [Add $69.95]
Black/Black (Hydraulic ) 3 inches Longer Than Stock, Teflon lined, Steel Braided [Add $76.95]
Additional Completion Products
Horn Extension Wire inches [Add $5.95]
Vibration Killers(12oz bar end weights) inches Heavy Bar-ends Kill Vibration [Add $42.50]
Honda VFR-800 Throttle Lines(00-07) 3 inches Stock+2 Inches (includes both lines) [Add $59.89]
Technical Specs Download
is a confirmed ConvertiBARS installation.
A confirmed installation means that ConvertiBARS, and or a customer, have successfully installed a ConvertiBARS Kit on a motorcycle within the range of years listed above and the rise listed below has been achieved, with or without longer lines, while being able to reach the steering stops without permanent damage to the motorcycle. The year range noted above is only an estimate of the years that the motorcycle appears to have had little or no change to the handlebars and fairing, and so the installer should find similar installation issues as noted in the bike specific install notes. A confirmed installation however, does not mean the kit is guaranteed to fit. ConvertiBARS is not liable for any labor times or costs associated with the installation or un-installation of either ConvertiBARS or the stock handlebars. Positioning restrictions between low and high positions do exist. See bike specific install notes for other installation and positioning issues.
*Maximum ConvertiBARS positioning capability.
Measurements are in inches, relative to the stock position, and with Proper Length Lines Position restrictions between low and high positions do exist. Measurements calculated with default handlebar below. See Bottom of page for rise capability with stock lines Fore = Further from the rider, Aft = Closer to the rider.
Important Installation Considerations.
Special dual brake line works with linked braking system. Remove the top line(2 lines with a junction block)and the hard cross over line. The replacement lines Both bolt at the master cylinder using a double banjo bolt and 3 washers. On the opposite ends, the line with the male threaded end, attaches to the clutch side crossover block. The second line attaches directly to the right caliper.
Honda VFR-800(02-09) Install Notes & Tips Sheet
*Max Rise allowed with stock lines.
Stock Hydraulic Brake Line
Stock Hydraulic Clutch Line
Stock Throttle Line
Stock Electrical Lines
*ConvertiBARS travel relative to the stock location; measurements are in inches.
CBR-600F4 & F4i (99-02)
CBR-600RR (03 only)
Hawk 650 (88-91)
VTR1000 Super Hawk
Honda CBR-900RR Bike Specific Kit
Honda CBR-600RR (04-06) Bike Specific Kit
Honda CBR-600F Hurricane(1990) Bike Specific Kit
Honda CBR-954 Bike Specific Kit
Honda CBR-600F2/F3(91-98) Bike Specific Kit
Honda VFR-750 Bike Specific Kit
Honda CBR-600RR (03 only) Bike Specific Kit
Honda CBR-1000RR(08) Bike Specific Kit
Share your knowledge of this product.
Be the first to write a review »